| BLOG | DIRECTIONS | SCHEDULE | STORE |
|
|
| BLOG | DIRECTIONS | SCHEDULE | STORE | |
Wednesday, December 7. 2011BN 9908, more steel... E units are long. Tuesday night several more steel parts were measured and cut out into the shapes that are needed for the patches around the nose. A couple of them will need a 95 degree bend for the nose door opening. One of the patches was welded into place on the firemans side of the nose. A few other areas that will never be accessible again were cleaned up and primed and/or undercoated. There are a few photos of the before and after on the carbody paint cleanup. There are more photos available shown here with the most recent being shown first.
Wednesday, December 7. 2011USA 8537 cab work
The United States Army 8537, a GE 45 ton diesel locomotive, was brought into the shop at the same time as the BN 9908. The purpose is to finish updating the cab interior by installing the new cab lights, a two way radio, permanently wiring the cab heaters, finish the painting inside the cab, and several other items. On Saturday the 3rd, the cab lights were installed, which are a standard EMD style. This required pulling all the old wire out of the conduit to the existing cab light and roof beacon and pulling it all back into the conduit, just to add one wire to provide constant power to the new lights. The lights are done now, along with the wiring to the cab heaters, which was run along the existing wiring in the electrical cabinet. They had been temporarily wired last year just to get heat in the winter months.
A number of years ago, Dan Currens installed a DC to DC isolated converter that took the 36V positive ground loco system to a 12V negative ground. The truck stlye cab heater motors, a priming fuel pump, and the two way radio run off the 12VDC system. The next step will be to wire in the radio and mount the AAR radio plate to the console. After that, more painting in the cab.
|
Blog AdministrationFind us on FacebookCalendar
QuicksearchArchivesSyndicate This Blog |
|||||||||||||||||||||||||||||||||||||||||||||||||
Comments
Mon, 06-17-2013 09:50
Wish I could be there to help.
Fri, 06-14-2013 16:50
Matthew, Any special event is the decision of the museum Board. My personal opinion is that it is likely that there would be a special event to [...]
Thu, 06-13-2013 18:33
Hi, I have a question, if or when she is restored and back up and running this or next year. Will their be a special event set up for the return of [...]
Tue, 06-11-2013 22:36
The whistle 1630 wore for a while that you're thinking of was a Frisco 6 chime donated by a former member of the steam shop. It was on it a few times [...]
Tue, 06-11-2013 18:03
You are talking here about something well before my time !. I have not seen her with anything other than the whistle she now carries. If she [...]
Mon, 06-10-2013 16:17
i'm curious here. Will 1630 ever wear the ATSF 6 chime she had on for a while? Better defines her, I love the deep whistle she has now but the higher [...]
Sat, 06-08-2013 15:15
Many many many many many thanks for getting the Spaulding webcam working!!!!!
Fri, 06-07-2013 16:55
The donation was to the museum as a whole. How it is used and whether any comes to steam department projects will be the decision of the museum [...]
Fri, 06-07-2013 16:53
Basically the plan is "ONLY" reassembly. As far as we know she is is reasonable mechanical shape. The big mechanical problem that stopped her (slack [...]
Fri, 06-07-2013 16:28
Nigel I read you guys got a one million dollar check donation!!! Will this be used to finish 1630 ,428, 5 and get started on the others next in line?
Fri, 06-07-2013 16:16
So does 1630 basically only need reassembly? With the boiler in particular. Does her tender or running gear need any work before she's ready for the [...]
Fri, 06-07-2013 12:00
Hello.. The voltage we are using and presumed the RR also used is 120 vac. The system is a little unique because the lite bulbs are each 60 volts. [...]