This was another productive day for the crew working in the Freight Car Department
Simon Harrison and Dave Rogan are the proud parents of a milestone accomplishment for our snow plow. Pictured here, BOTH plow wings are now operational and can be extended or retracted. At the lunch table we invited any of the volunteers on site to come over and get a chance to operate the wings - many did just that!
The wings may move about 36 inches outward, and many may have the misconception that they swing much farther. As we got the plow it was repainted by the CNW into its yellow scheme. But behind the plow wings lives the CGW bright orange from the 1970's. Some say CNW stands for Cheap & Nothing Wasted, - in any case they apparently sprayed all around the exterior but did not bother to open the wings and finish the job.
Jim Leonard continues to wrestle with well rusted nuts and bolts on the roofwalk.
Buzz Morisette is making good progress with framing repairs and now is laying down new flooring in the carbody box, between the doors on each side.
Simon Harrison is chipping high on the car side, only a few areas left to clean up on the north side, and then on to the finish paint.
We do not look down on our volunteers, but I had a chance while up on the roof to get this unusual angle of Simon and Dave working just below the edge of the roof line.
Modelers may be interested in this shot of the cab roof. It was almost a spotting feature of the CGW (their steel cupola cabooses also had this) that a handrail was installed around the perimeter of that small roof. Most other railroads did not go to the expense.
The handrail was supported by eye bolts and at the corner it was rounded.
Also this week, a separate crew finished the second coat of new paint on our Borden's Milk Tank Car. That was good.
Those of you patient enough to read this far - we would like to extend an invitation to all those members and friends who plan to come out for Museum Showcase Weekend. On Saturday 9/15 about 1:30 PM we are going to do a demonstration of the snow plow wings in action. And ANY of you physically able to get up into the plow, and to its cab (not yet restored) are invited to try your hand at the controls. Of course, first come, first served, and if 50 of you are hoping for this rare experience, well - we will do what we can. Did any of you wonder what it was like to run such a plow, to have the power in your hands to swing the wings, to have bragging rights over your fellow railfans or modelers? Now is your chance for this rare opportunity not available to the general public.
Here are a few shots I got as I passed through the shop this week.
One of the new letterboards has been installed on the north side of Lake Shore Electric 810. When the remaining pieces are done on this side, it will be on to the roof work. George Clark, Gerry Dettloff, and John Faulhaber worked on the project today.
Rich Witt continues to restore windows for the Chicago Aurora & Elgin 36. It is not likely he will run out of work soon!
Our upholstery wizard, John McKelvey, is working on the seats for Chicago Rapid Transit 1797. Plenty of repair work to be done, some totally recovered.
Buzz Morisette was working on the CGW X 38 snow plow earlier but here, he is planing new wood destined for our dynamometer car, MILW X 5000.
We split the crew today, more on that later. Here Dave Rogan and John Faulhaber are ready to try to open the left side wing on the plow. They had already done some of the prep work and fixed more air leaks, and charged the reservoirs to 50 psi. This had never been tried at IRM and perhaps not been moved during the previous 20 years.
Many of the volunteers migrated to what we hoped would be a successful trial. We had several working - Dave Rogan working the controls up in the cab, Henry Vincent watching the air pressure gauge inside, others to pass along verbal instructions. IT MOVES!!! We all expected loud squeaking and protests from the hinges, but it was completely smooth and quiet - we almost missed it.
Here, Henry Vincent, Buzz Morisette, John Faulhaber, Dave Rogan and Rich Witt beam proudly. To deal with one of the leaks, we removed the whistle valve and capped the air pipe. In the shop Rich Witt dismantled that, and we found the spring inside had been assembled in the wrong position - apparently an artifact from an indifferent mechanic on the CNW.
There it was wide open, and we peered to see behind what had been
cloaked to all of us. The CNW never opened them up when repainting, and
the last CGW orange paint remained. Henry and Rich Witt look for clues
Gerry Dettloff fabricated a new steel strap to support the roofwalk. One was missing due to a broken weld and we needed it in place to continue installing interior wood framing on the back wall. The bolts pass through the straps, end wall, and the wood timbers.
I opened this entry saying we had split the crew. Here, Victor Humphreys and Jim Leonard work to repaint the Borden's Milk Car. Prepped and primed last week, it was now time for the first coat of finish paint. In true IRM spirit they continued the painting during the plow wing moving tests. Thanks guys!
Comments
Mon, 09-08-2025 08:22
Good job on the Burlington Nortern 9976. OK.
Tue, 08-12-2025 12:56
No new news that I have heard of thus far.
Tue, 08-12-2025 12:53
I'll also be doing another update on it soon. Keep en eye out for that.
Tue, 08-12-2025 12:47
A little work was done to it for Diesel Days this year. You'll see photos floating around for the temporary short term job that was done to make it [...]
Wed, 08-06-2025 13:01
Is steam car CN 15444 going to be coming to museum several times it was to be moved to muesum
Sat, 07-19-2025 18:56
Yeah, sadly it's still there as of 7/19/2025
Thu, 06-12-2025 19:14
Its been 14 years guys, where is the unit? Like really? Did you guys misplace it? Or are repairs taking that long? At this point be might we will have [...]
Wed, 04-09-2025 17:40
Jamie Thanks for the update. She's gonna shine like every thing else you guys do! Smeds
Thu, 03-06-2025 16:28
Yes, there is a wye. Those two have been MU'ed on diesel days a year or two ago.
Wed, 03-05-2025 14:04
7009 number boards look good. Is there a way to turn a locomotive around at IRM? In case you ever had a mind to connect 7009 and 6847?
Fri, 03-29-2024 21:26
We're slackers and spend more time working on the equipment in the shop than keeping all you readers updated. We'll work on it, but I'm sure updates [...]
Thu, 03-14-2024 08:02
What happened to the Department Blog? It's been over 2 years and I still regularly check for updates, but nothing comes...