Steam Department

The number of people in the shop was a bit reduced at Easter weekend and it was unfortunately one of those days when a lot of hard work did not achieve as much as was hoped. 

On 1630:

·         The main focus was on loading the super heater flues.  Unfortunately this proved a great deal more tricky than had been hoped. 

When the tubes were safe ended each was carefully measured with the objective that it was matched to a specific location with a certain amount of excess length to be ground off after fitting.  When the first few were fitted it became clear that there is a significant variation from the intended lengths with some shorter and some longer.  Clearly, where there is excess length it can be cut off.  But if we have any that are too short to be fitted we would need to get more welding done.

The key objective became to ensure that the shorter ones can all be used without the need to get a welder in again to lengthen any.   So, instead of simply slotting each tube into its numbered hole, it became an exercise in loading and unloading tubes multiple times to ensure that the shortest tube that provides the required projection at each end is used in each hole. 

As each tube is 17 feet long and 5 1/2 inch in diameter, they are heavy beasts to fit and refit so it was a hard day's work made worse by the fact that it was unexpected.  The first part is easy.  The fork lift raises the tube to height and in this shot, Phil and Sean slide the tube into the hole in the tube sheet.

Phil and Sean load a SH flue

The next bit is more tricky.  Once the tube is off the forks it becomes a giant lever pivoted in the tube sheet.  Here Dave is assisting by controlling the end of the tube to ensure that is slides smoothly thru the hole and can be located in the rear sheet without dislodging the ferrule at that end.

Sliding the flue into place

Once it is in place there is a careful process of gauging the projection at each end to ensure we have the required 1/4 inch minimum.  Given the length issue, a number were then removed and the process repeated to ensure that the shortest suitable tube was used in each hole.  Anyway, by end of day we had all 8 on the engineer's side in place and the first on the fireman's side and have managed to place the shortest tubes..

·         With Vince's assistance, Mike finished the tapping for the patch screw on the firebox corner.  When I left sparks were flying from inside the firebox as Mike did the final grinding of surfaces inside the firebox ahead of riveting.  We are waiting on the return of the air bucker from overhaul and can then set up for the riveting.

Thread cutting for the patch screw

·         Ed and Richard substantially completed the pipe runs along the boiler sides and started work on the cab pipe work.

·         During the last couple of weeks Kevin has done more needle chipping to prepare for painting both on 1630 and on the planer.

Elsewhere:

·         Bob continued work on wiring the control system for the planer; and

·         Dennis finished building up the grease keep for the truck axle box on 428.

So next week we target fitting of the remaining flues and then we can set up to roll them into place.

Nigel

Not too much visible progress in the steam shop this weekend but actually a good deal that is not very apparent.

On 1630

·         The first two super heater flues are now loaded.  This involved identifying and learning how best to use a whole array of new equipment.

First 2 super heater flues in place

o   Jason successfully expanded ferrules into all 16 holes in the rear tube sheet last Sunday.  These were chosen from two alternate thicknesses to provide a close fit on the flue as it is inserted from the front of the boiler.

o   For the large flues the loading process is, of necessity, more complex.  Ferrules will be fitted in the front sheet only where the hole is enlarged beyond 5 1/2 inches in diameter.  From measurements made yesterday this will be 10 of the 16 flues.

o   Fitting the front ferrule is very much part of the loading process.  Given the size and weight of a 5 1/2 inch tube 17 feet in length, there is no possibility of expanding the ferrule into the sheet in a way that would allow the flue to passed thru the ferrule without displacing it.  So the flue must be passed thru the front sheet, into the back sheet and pushed several inches beyond its final position into the boiler, clear of the front tube sheet.  The ferrule can then be fitted and the flue drawn back into the front sheet.  So fitting the front ferrules is an integral part of loading the flues.

o   Initial progress was slow as the ferrules must be expanded to the absolute limit of our largest rollers, which meant that they were not very secure.  During the day we made a spacing ring that overcomes the problem so, based upon experience with the two now in place, we believe the rest should be much quicker.

·         Jane continued priming the inside of the cladding sheets so that these will all be ready to install over the lagging.  She has now completed the batch we have in the shop so we will need to store these again and get another batch for cleaning and painting.  The cladding will not look good at this stage as the outer face will not be prepared and painted until it is in place.  However, priming the inside where it is subject to heat and damp from the lagging, is essential to preserve the sheet on the locomotive.

·         Eric and his Dad worked from pictures of the backhead, that we took before stripping, to locate all the valves and controls, lay them out in the machine shop and start work on servicing, cleaning and painting them.

·         Dennis weld filled the hole for the one patch screw that must be replaced.  Mike and Tom then produced a guide and started to drill out the hole for threading.

·         Dennis weld repaired the two super heater elements that failed under pressure test last Fall.  (Actually Dennis did this a couple of weeks ago and Nigel did not notice !!).  Anyway, these are now ready for hydro testing once we get above freezing outside.

SH elements repaired

On 428

·         The first of the two guides for machining the shoes and wedges was competed and Tom is starting to finish the ends of the cast iron shows on the shaper.  The second, which will enable the machining of the angle on the wedges is approaching completion.

Mounting shoe in shaper

Finishing the end of an axle box shoe

·         Dennis was brazing the grease cellars for the truck axle boxes.

In other areas:

·         We moved the turret covers for #265 up on to the top of the locomotive.  Time is moving on and the museum opens to visitors soon.  We would be deeply unpopular with Buildings and Grounds if large lumps of metal are in the walkways of barn #9 as opening day approaches !

·         We had hoped to get some tubes for the Shay out of the boxcar but investigation proved that this can only be done with fork lift access to the car as other heavy material must be moved to get at the tubes.  (For efficiency we want to swage the Shay tubes when we do a few extra required for 1630.  It takes several hours to set up and test the swager so we want to do a full batch rather than 5 tubes when we do so).  However, we will now need assistance to shunt the KCS tender and re-spot the boxcars before we can do this.

·         Glenn and Richard worked on the safety covers for the new compressor.

·         Glenn assisted the track department in trying to start their crane.  Unfortunately this proved "non trivial" as it seems the fuel lines are blocked.  So it did not start today.

·         Jeff was finalizing the air supply in the new shop. - Yes this is Jeff.  The extent of the hair cut led many to question if we had a new volunteer this weekend !.

New look Jeff works on the air supply

Most of the new outlets are now in place.  These are all being structured with a drain on each down pipe to avoid water carry over.

Air supply at wheel lathe

·         Bob carried on from last week, positioning the planer.  It is now not only in position but pretty much level.

So a good day's progress and hopefully we are now set up to move forward quickly next weekend.

Nigel