Steam Department

A sharp but, if the forecast is to be believed, brief improvement in the weather allowed us to do a series of moves of material in and out of the shop this weekend.  Spare tubes and flues were moved out of the shop into the boxcar and the fire bricks that make up the arch in 1630’s firebox were brought in from the water supply car.  This gives us more room in the shop and jobs that we can continue if we have to hunker down in the shop for a few weeks!.

·         Cameron had finished and fitted the stud during the week and we were able to ensure that it is leak free.  This enables the boiler to be opened up and thoroughly dried for the Winter and also means that the insulation can be refitted;

·         Jane was hard at work much of the day painting many different things including mounting brackets for the equalizing reservoir and a lot of infill sections for the sheet metal.  This is one of the jobs that will require quite a bit of work over Winter.  Wherever a pipe or bracket projects thru the lagging there must be a hole in the sheet metal.  It is rarely possible to simply have a hole in the big sheet metal section to tightly fit around the projection (as the sheets must be moved around to fit them).  So smaller sections of sheet metal must be fitted around the projection under the main sheets to stop water getting in and damaging the insulation.  The tests indicated a lot of areas where we need to seal small holes;

·         Jerry put in a solid day on the insulation.  He has refitted all the insulation that was removed to trace the steam leak from the lubricator line and has made substantial progress on the panels each side of the firebox. 

The insulation is now back in place

These are an absolute pain as they must be removed annually to inspect the ends of the rigid stays.  So there are areas where the insulation blocks are secured to the sheet metal rather than the boiler.  To add to the challenge, some of the sheets cover areas where part of the insulation is fixed to the boiler and part to the panel so the insulation must be cut so that the insulation must interlock when the sheet is fitted ………. while maneuvering it around and behind various fittings.  My guess is that this is a modern problem.  From memory of working with asbestos matting in the early 1970’s (yes I did that that apparently survived !) is that it had much more strength than the modern “safe” insulation, which tends to fall apart very easily;

·         Ed worked on cleaning the water glasses which were noted as not showing clearly during the test.  (The glasses have a reflective surface that provides a clear indication at night under limited illumination and so need occasional “deep cleaning”);

·         Jason and Trevor removed some wash out plugs and the inspection hatch. 

Trevor and Jason remove the hatch

The air blower was then fitted so that a constant air flow will be maintained thru the boiler for a week or so to ensure that it is thoroughly dry for the Winter;

·         Cameron had painted the equalizing reservoir during the week so Phil and I set out to hydro test this ready for refitting.  Set up for pressure testing is always slow as you have to find / make a suitable combination of fittings to link from the pump to whatever fitting happens to be on the tank that you want to test.  Having done this and connected the air and water it became clear that the main pressure hose from the pump has developed a leak !!.  Ho hum !.  That is now a job for next week once the hose has been professionally repaired;

·         The fire bricks were moved into the fire box in preparation for another fun task.  The arch is built from a number (I currently think 4) differently shaped bricks that fit between arch tubes, from arch tubes to firebox wall etc.  We need to plan out exactly how many of each are required and identify any that we are short of so that we can have a suitable supply on hand for next season.  It is likely that we do not even have a pattern for one type so will need to make the wooden pattern from which the bricks are cast using one of the existing bricks as a model;

·         Jason started removing the blower line in the cab.  This had a small leak detected during the test run so is one of a number of the pipes in the cab that we plan to adjust and refit during the Winter.

With 1630 in reasonable shape, Brian, Cameron and Phil did quite a lot of work on #428, where much of the current focus is on the brake gear:

·         Brian and Cameron have been working steadily thru the brake shoe holders.  These have now all been drilled out for fitting of the mounting pins.  As with much of this locomotive, years of wear and limited maintenance meant that holes had become substantially oval.  The repair has required filling the hole, by welding in new material, and then re-cutting the holes to the original size.  In this case 8 brake shoes , two hole per holder so 16 substantial holes to be filled and re-cut;

Drilling the brake shoe holders

·         With this done, focus is now moving to other components of the brake rigging.  The second of the main shafts was removed (from the engineer’s side) so that both can be worked on together.  This sounds easy but the things weigh more than 100 pounds and had to be extracted from its mounting under the locomotive then rolled / man handled over the track between the wheels to get to the fork lift (no pictures as I was operating the fork lift !);

·         Trevor was working on the frame that is required to support the pistons so that the heads can be built up with braze metal.

On the Shay, Jason and Trevor finally managed to remove a wash out plug from the belly of the boiler that we have been fighting with for a long time.  We do not know when it was last removed.  It is above the front truck and not easy to reach.  History suggests that, when the loco was last running, it was impossible to remove as it was far too tight to extract in the confined space above the truck.  Having finally extracted it using heat, lots of penetrating oil and very long cheater bars !, we can now understand why.  Someone long ago must have put it in wrongly threaded and solved the problem of leakage by tightening with great force.  Absolutely what you should not do with a brass wash out plug!.  Oh well, it will now be remade and fitted gently.

Bob, Ed and Jane continued work on the planer.  This is now just about fully painted and looks really great. 

Ed inspects the planer

Much of the effort was directed to pumping degreaser thru the various oil passages to remove as much debris as possible before filling with oil.  Much of the effort was directed to trying to see as much as possible of the interior passages to determine how effectively the debris had been removed!.  The same oil is used to lubricate the machine and provide the hydraulic power that moves the bed back and forth so removing debris and placing filters is rather important.  Most of the shop are now waiting with great anticipation to see the machine work.  The team seem to be non- committal about when they will bite the bullet, fill it with oil and see what happens !!.

So a day of steady progress in a number of areas.

Nigel

Wow!.  The Winter temperatures have certainly arrived with a bang this year.  This time last year we were happily moving tubes in from the boxcar.  This weekend anything outside was done quickly and in heavy clothing.  At 20 degrees with a strong wind most work was done inside.

However, we did manage to ensure that the drop pit pump and anti-frost heating are working and move the Sullair into the shop so that it should start if required.

On 1630:

·         Matt and Jim produced new washers for the water connections between the tender and the injectors.  The filters baskets were passed to Dennis to work on the brazed surfaces.  Hopefully the combination of these two actions will provide a long term fix for these connections that have tended to leak for some years.

·         Rick made good progress on fitting the sheet metal screws to secure the radius pieces of the sheet metal on the back head.  Once this and a couple of other jobs are done we should be able to paint the firebox in the cab.  That promises to be great fun working around all the pipes and fittings!.

·         Eric did some hours of laborious needle chipping to remove paint from the driving wheels.  Kevin did a lot of this some months ago.  Now that the locomotive is in a different position, the rest of the wheels can now be cleaned off ready for painting.

Eric needle chips the drivers

·         Ed and Bob remade the copper pipe connection for the steam heat line;

·         Matt refitted the reflectors to the gauge lights.  These should now be a lot brighter;

·         The last of the three air tanks below the walkway was removed for painting.  In addition, I worked with Collin and Matt to remove the small equalizing reservoir from under the cab floor so that it can be hammer and hydro tested.  This is small but a real pain as it is surrounded by a bunch of pipes that run just below the cab floor.  In the photograph below you can just see the end of the reservoir in this view under the cab on the engineer's side.

The reservoir in situ

Here Collin is squeezed between the locomotive and tender working on the nuts that secure the reservoir to the back of the locomotive.

Collin releases the reservoir

Anyway, after much cussing and tricky maneuvering, it was extracted.  By end of day, I had successfully hammer tested and primed it.

·         Jerry made good the insulation on the fireman's side, that was removed to fix the leaking lubricator line.  He then started on the lagging of the firebox side sheets.  These are unusual when compared to all the other insulation.  As they need to be removed annually to inspected the firebox side stays, the insulation is attached to the sheet metal rather than the boiler;

·         Dennis continued work on the sheet metal for the smokebox.

·         Cameron and Brian worked with Tom to machine the new stud.

In other areas:

·         Phil prepared the bolster of the Shay by removing the last loose spring locator.  Once Dennis welds in the new locator we can start planning to put the bolster and springs back into the truck.

·         Tom completed machining the first wedge for the axle boxes on #428;

·         Brian and Cameron continued drilling the brake hangers for #428;

·         Cameron worked on the moulds that are required for the casting of the babbit bearings for the cross heads;

·         Bob and Ed worked on preparing the oil system of the planer for filling.  The challenge is the best way to get debris out of the system before filling it with the approximately 80 gallons of oil with which it will operate;

·         Brian brought in the replacement switch for the forklift and this was fitted.

So it was a successful weekend as we continue to work thru the Winter maintenance tasks.  Next weekend will provide a good opportunity to work off the effects of the turkey !.

Happy Thanksgiving

Nigel